Succes on testing port from "BEGIN" failure when press "check" in pc wintech win

[wierdtaz]

Sir,

Re. TP-Link TL-WR 641G

I had two routers and connected them using DMZ as given in tutorial, while at another location i have single router which i succesfully port forwarded and working file while here in the other case (two router case) after using DMZ scenario seen is as under:

when i press begin to test the port:
i am able to see success "# port is online and can be reached"

while when i press check in the window on right just above this message, while everything is same it says:
"# port is offline and cannot be reached"

also on canyouseeme.org, port is shown as connection refused.

Can admin or some other user guess what is going on! how is it possible? why is it showing succes at one place in window open: success, while atthe same time failure in same programme but on HTML page.

I am so confused and had been trying so long to sort this out but failure can admin even help me on TV please or just give guidance.

PHOTOS ATTACHED FOR EXPLANATION
Regards,

Thanksin advance

[attachments over 25 days old deleted by admin]

[Shane]

That is because my program actually opens and listens on the port itself.

If nothing is using the port the test will fail no matter what 

Shane

[wierdtaz]

That is because my program actually opens and listens on the port itself.

If nothing is using the port the test will fail no matter what 

Shane

Please advise what should i understand from this?? couldnt unerstand that argument!!

Further, when i use the other router and port out uing siml port frwrding and when test that it shows online by both buttons "begin" and "check"!

couldnt understand what is the prolem with the other one, i was behind two routers as you know, looks like i am doing something wrong! can you please pont that out !

[Shane]

Give this a read to understand what port forwarding is and why you need it, pretty simple really 
http://www.pcwintech.com/what-port-forwarding-nutshell

So on your computer, when the port tester works it is sending a connection attempt on that port. Well if nothing is using the port to get the connection it will fail.

What my port tester does is it opens and listens on the port for the test connection. This way you know if it is working or not.
Thats why I made the program


Now on the 2 router setup. How did you setup the DMZ? what Ip did you put into the the first router DMZ? It should have been the WAN/Internet IP of the 2nd router

Shane

[wierdtaz]

Give this a read to understand what port forwarding is and why you need it, pretty simple really 
http://www.pcwintech.com/what-port-forwarding-nutshell

So on your computer, when the port tester works it is sending a connection attempt on that port. Well if nothing is using the port to get the connection it will fail.

What my port tester does is it opens and listens on the port for the test connection. This way you know if it is working or not.
Thats why I made the program


Now on the 2 router setup. How did you setup the DMZ? what Ip did you put into the the first router DMZ? It should have been the WAN/Internet IP of the 2nd router

Shane

Thanks i understand what you mentioned! Furthe ri want to say that before setting up

DMZ exactly according to the way which you mentioned in your tutorial, only it showed

succes on testing it by "BEgin" otherwise before setting that up in thi sway, it was

showing the port as offline whether we press "begin" or check doesnt matter.

While now it shows Online when we press begin test, while shows offline when we press

checkport in the small browser window, where results are shown. and whnen i am trying

to run the programme that is also no running well means port in actual is not open!

can you please on team viewer ??? it will take 5 minutes for you to point out the

issue.

i am sending you what ips i am putting in dmz and etc. yes it was same WAN/IP address!! while in 2nd router i have not disturbed or enabled DMZ it was not the requirment i hope so, only enabled DMZ in 1st router+modem to direct everything to second router

Results of ipconfig:


   Description . . . . . . . . . . . : Intel(R) Wireless WiFi Link 5100
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.2.100(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Tuesday, August 31, 2010 10:12:46 AM
   Lease Expires . . . . . . . . . . : Tuesday, August 31, 2010 12:52:06 PM
   Default Gateway . . . . . . . . . : 192.168.2.3
   DHCP Server . . . . . . . . . . . : 192.168.2.3

DNS server 192.168.1.1
      192.168.2.3   

please check attached all photos for all possible settings and advise back at soonest!thanks for your un-beatable support and excellent programmes





[attachments over 25 days old deleted by admin]

[wierdtaz]

Give this a read to understand what port forwarding is and why you need it, pretty simple really 
http://www.pcwintech.com/what-port-forwarding-nutshell

So on your computer, when the port tester works it is sending a connection attempt on that port. Well if nothing is using the port to get the connection it will fail.

What my port tester does is it opens and listens on the port for the test connection. This way you know if it is working or not.
Thats why I made the program


Now on the 2 router setup. How did you setup the DMZ? what Ip did you put into the the first router DMZ? It should have been the WAN/Internet IP of the 2nd router

Shane

Thanks i understand what you mentioned! Furthe ri want to say that before setting up

DMZ exactly according to the way which you mentioned in your tutorial, only it showed

succes on testing it by "BEgin" otherwise before setting that up in thi sway, it was

showing the port as offline whether we press "begin" or check doesnt matter.

While now it shows Online when we press begin test, while shows offline when we press

checkport in the small browser window, where results are shown. and whnen i am trying

to run the programme that is also no running well means port in actual is not open!

can you please on team viewer ??? it will take 5 minutes for you to point out the

issue.

i am sending you what ips i am putting in dmz and etc. yes it was same WAN/IP address!! while in 2nd router i have not disturbed or enabled DMZ it was not the requirment i hope so, only enabled DMZ in 1st router+modem to direct everything to second router

Results of ipconfig:


   Description . . . . . . . . . . . : Intel(R) Wireless WiFi Link 5100
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.2.100(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Tuesday, August 31, 2010 10:12:46 AM
   Lease Expires . . . . . . . . . . : Tuesday, August 31, 2010 12:52:06 PM
   Default Gateway . . . . . . . . . : 192.168.2.3
   DHCP Server . . . . . . . . . . . : 192.168.2.3

DNS server 192.168.1.1
      192.168.2.3   

please check attached all photos for all possible settings and advise back at soonest!thanks for your un-beatable support and excellent programmes

another photo DMZ in router kept disabled

[attachments over 25 days old deleted by admin]

[Shane]

If my port tester says it passes when you click begin then the port forwarding is working. So don't stress about that 

You have everything setup right.

So if you still have trouble with the program your hosting then the problem might be else where.

What problems are you having when you run you server/game?

Shane

[wierdtaz]

If my port tester says it passes when you click begin then the port forwarding is working. So don't stress about that 

You have everything setup right.

So if you still have trouble with the program your hosting then the problem might be else where.

What problems are you having when you run you server/game?

Shane

I am running CYbergate, it is remote control application, when the server is run on another computer it notifies me here on cybergate through the open port, but it is not doing so now.. !! then i should check something else!! thanks for confirming that settings are all ok, further also i am now checking other things like i am using no-ip service, let me check that and i will update you!! but cannot understand as it should not be acting like this while when i connect with all same setup but with other ourter at my home it all works fine, cybergate also works fine!!

i shall definitly come back ery soon Thanks for help

[wierdtaz]

If my port tester says it passes when you click begin then the port forwarding is working. So don't stress about that 

You have everything setup right.

So if you still have trouble with the program your hosting then the problem might be else where.

What problems are you having when you run you server/game?

Shane

I am running CYbergate, it is remote control application, when the server is run on another computer it notifies me here on cybergate through the open port, but it is not doing so now.. !! then i should check something else!! thanks for confirming that settings are all ok, further also i am now checking other things like i am using no-ip service, let me check that and i will update you!! but cannot understand as it should not be acting like this while when i connect with all same setup but with other ourter at my home it all works fine, cybergate also works fine!!

i shall definitly come back ery soon Thanks for help

Thanksss it is working finee... thank you very much sir... and your tutorials are reallly great!!! thumbs up....

[Shane]

Good to hear your set

Since your all fixed I will lock this thread. 

And as always, all I ask in return...
If your happy with my work. Then all I ask in return is you simply let others know about my site and programs. I do a lot more than port forwarding
Also always feel free to make a post in the feedback forum.


Shane